Tag Archives: Rig of the Month

Rig of the Month– Henny Penny’s Pikeminnow Bait

Story and photographs by Don Talbot

Chicken liver balls are a great bait to use for pikeminnow when you’re sitting on anchor in a hole and looking to draw in hungry fish.

ROTM 2

Step 1

Step 1: Gather the following supplies to make 250-plus chicken liver balls:
• 6-foot-long work table
• Bowl of water and sponge to wet the table
• Scissors
• Five containers of chicken livers
• Five packs of Spawn Net
• Two packs of Miracle Thread
• Attractant


Step 2:
Cut the Spawn Net up into squares. Each pack makes 50 to 60 squares.

ROTM 3

Step 4

Step 3: Wet the table so that the netting doesn’t blow away, and then place the squares in rows up and down the table.


Step 4:
Cut the chicken livers into thumbnail-sized chunks and place each in the middle of a square.

ROTM 4

Step 5

 

Step 5: Grab and twist the four corners of the netting together around the liver.

rotm 5

Step 6

Step 6: Wrap the Miracle Thread around the twisted liver ball end 10 times and pull to break.

Step 7: Cut the tag end of the netting off and place the bait into the chicken liver container.

ROTM 6

Step 7

Step 8: Marinate with your favorite fish oil – this is one of my secret weapons! I use Super  Dipping Sauce in garlic scent.

Step 8

Step 8

 

 

Step 9: Put the loaded containers back into your refrigerator or freezer. I like to keep my liver balls on ice, as I like fresh bait most of the time for pikeminnow fishing.

 

 

HOW TO RIG

ROTM 8

Step 1: Load your reel with 100 yards of 20- to 30-pound braided line, which helps to detect the bite better.
Step 2: Slide a snap swivel up the braid to clip to a 1- to 6-ounce cannonball, and then add a 6mm rubber bead or other bumper to help minimize metal-to-metal noise.
Step 3: Tie a good barrel swivel to the end of the braid and then attach a 3-foot-long, 20-pound-test leader rigged with a size 4 Gamakatsu hook.
Step 4: Barely hook the liver ball so that the fish will hook itself while biting the bait.
Step 5: Dunk in your favorite marinade and cast away. NS

Rig Of The Month: Estuary Sturg ’n ’Nook Quick-change Set-up

NOTES

Getting a chance to pull off a successful combo fishing trip is very satisfying, but it usually involves such long days and so much gear that it feels daunting to even attempt. This rig simplifies things.

With the rise of a new summer Chinook fishery in the Columbia River estuary just above the AstoriaMegler Bridge, many anglers will be making the trip here this season. But with salmon fishing so concentrated towards the last part of the incoming tide, it will leave many wanting more. Enter the very healthy population of hungry sturgeon roaming these waters this time of year. Retention is closed, but there’s nothing more exhilarating than hooking into multiple fish that will put you and your gear to the test.

No special tackle is needed for sturgeon – your salmon rod and reel will work just fine. And it just so happens that those fresh anchovies you bought for Chinook are a favorite of estuary sturgeon. Check the tides and target diamondsides from low slack and halfway
through the incoming before pulling anchor and making a run to the Washington side above the bridge to fish salmon for the last half of the incoming through high tide. – Andy Schneider

(Andy Schneider)

(Andy Schneider)

Rig Of The Month: Channel Cat Set-Up

Standard operating procedure for plunking for most species that hunker near the bottom is an egg sinker, bead, swivel and long leader to lift your bait out of the weeds, and that’s certainly the case with this channel catfish set-up. However, where it differs is with that 2-inch-long float, which does not go above the sinker, as with eggs or worms under a bobber for stocker trout, but actually in the middle of the leader. While channels have whiskers to find food on the bottom, they also will rise to grab a bait. The float allows for scent to be broadcast more widely than if the bait’s anchored to bottom. –NWS

RotMtemp